Tuesday, February 21, 2017

Monday, February 6, 2017

Do you know Eleaf iStick Pico?

The iStick Pico, just like its name, is tiny and exquisite in appearance. Powered by single interchangeable 18650 cell, it provides you with 75W maximum output and switchable VW/Bypass/TC-Ni/TC-Ti/TC-SS/TCR Modes. With top e-liquid filling design, hidden airflow control and detachable structure, the new MELO III Mini is the best match for the iStick Pico.
http://www.istick.org/eleaf-istick-pico-75w-tc-box-mod.html

1. About Power on/off: 

Screw off the battery cap, put one high-rate 18650 cell (positive side down and negative side up) into iStick Pico and finally screw on the battery cap. The device can be powered on/off by pressing the fire button 5 times.
Note:
1. Please make sure you are using a high-rate 18650 cell whose continuous discharge current should be above 25A.
2. Please be careful not to use cell with torn casing as it is a safety hazard.
3. Before using, please set the wattage within a proper range that the atomizer you installed can work with.

2. How Vaping:  

Long press the fire button to take a puff.

3. About Stealth on/off: 

Press the fire button and down button simultaneously when the iStick Pico is powered on to switch between Stealth On and Stealth Off mode. In Stealth On mode, you can vape with the OLED screen off and you can press the fire button one time to see current setting.

4. About Adjustment buttons lock/unlock: 

Keep pressing up button and down button simultaneously for two seconds when the device is powered on, then the up and down buttons will be locked and the screen will display “Lock”. In the same way, the up and down buttons can be unlocked and the screen will display “Unlock”. Through this operation, you can protect the buttons from unintentional presses and prolong their lifespan.

5. About Switch display mode: 

Keep pressing up button and down button simultaneously for two seconds when the device is powered off, the screen display will rotate 180 degrees. You can view the screen from two different angles through this operation.
Switch vaping modes: When the device is powered on, press the fire button 3 times in quick succession, the device will display current vaping mode. Press the up or down button to switch among VW, Bypass, TC-Ni, TC-Ti. TC-SS, TCR-M1, TCR-M2, TCR-M3 modes and then press the fire button one time or stay in the interface for about 10 seconds to confirm the vaping mode you chose.
1) In VW mode:
When set in VW mode, the device can support a coil whose resistance is within the range of 0.1ohm-3.5ohm.
Adjust wattage: In this mode, the output wattage can be adjusted from 1W to 75W by pressing up button or down button, up button to increase and down button to decrease, Long press up button or down button can rapidly increase or decrease the wattage level.
2) In Bypass mode:
When set in Bypass mode, the device can support a coil whose resistance is within the range of 0.1ohm-3.5ohm, Direct output voltage system is applied in this mode. The higher the battery level, the higher the output Voltage.
3) In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2, M3) Mode:
When set in TC-Ni/TC-Ti/TC-SS mode, the device can separately support Nickel 200, Titanium, and Stainless Steel 316 coils. In TCR (Temperature Coefficient of Resistance) mode, the device can support different temperature control coils within different TCR value ranges and you can set the TCR at different values within proper range. (Resistance range of coil: 0.05ohm-1.5ohm)
The Setting of TCR Mode (M1, M2, M3): When the device is powered off, keep pressing the fire button and the up button simultaneously, then you will enter into the TCR (M1, M2, M3) set menu:
1. Press the up or down button to choose among M1, M2 and M3 modes;
2. Press the fire button one time to confirm the mode you choose;
3. Press the up or down button to increase or decrease the TCR value according to the material of the coil you use;
4. Keep pressing the fire button or stay in the interface for about 10 seconds to confirm your setting.
Follow are different TCR value ranges for different coils for your reference:
Note:
1. The TCR value in the sheet is 10 multiplied of the actual TCR.
2. Our total range of TCR value is 1-1000.
Adjust wattage: In TC-Ni/TC-Ti/TC-SS/TCR (M1, M2, M3) mode, the output wattage can be adjusted from 1W to 75W. Press the fire button 4 times in quick succession to enter the wattage setting menu and press up or down button without looseness to rapidly increase or decrease the wattage level.
Adjust temperature: In TC-Ni/TC-Ti/TC-SS/TCR (M1, M2, M3) mode, temperature can be adjusted from 100-315℃ or 200-600℉ by pressing up button or down button, up button to increase and down button to decrease. Each press of the up or down button will increase or decrease the temperature setting by 5℃ or 10℉. Keep pressing up button or down button without looseness can rapidly increase or decrease temperature setting.
Shift between ℃ and ℉: If you increase the temperature to 315℃, and continue to press the up button, the temperature reading will automatically change to the lowest Fahrenheit (200℉). Equally, if the temperature reading will automatically change to the highest Celsius (315℃).
Lock/Unlock resistance: In TC-Ni/TC-Ti/TC-SS/TCR (M1, M2, M3) mode, when the device is powered on, keep pressing the fire button and up button simultaneously for two seconds to lock or unlock atomizer “base resistance”. The lock sign will appear when resistance is locked and “Ω” symbol will come back when unlocked.
Note:
1. Please lock the resistance when the coil is at room temperature so that the device can display the correct “base resistance”.
2. In resistance lock mode, when you remove the coil and then put it back, the device can maintain the same “base resistance” although the coil resistance may increase due to the rise of temperature. In resistance unlock mode, when you remove the coil and then put a coil back, the screen may display “New coil up same down” as the coil resistance may increase within certain range. If it is the same coil, press the down button and if it is a new coil, press the up button. But please unlock the resistance when you want to change an atomizer or a coil of different resistance.
3. When using a common coil or a coil whose resistance is above 1.5ohm in TC-Ni/TC-Ti/TC-SS/TCR (M1, M2, M3) mode by mistake, the device will automatically switch back to VW mode.
The post powered by Well-known E-cigarette brand "Eleaf", any questions about iStick Pico, you can contact Eleaf official authorized distributor online store - www.istick.org official facebook page.

Thursday, February 2, 2017

Warnings for Eleaf iJust ONE Starter Kit

1. Please keep out of reach of children.
2. iJust ONE is not recommend for use by young people, non-smokers, pregnant or breast-feeding women, or persons who are allergic/sensitive to nicotine.
3. Do not attempt to repair the device by yourself as damage or personal injury may occur.
4. Do not leave the device in high temperature or damp conditions, otherwise it may be damaged.
5. Do not use Eleaf iJust ONE Starter Kit for other purposes except only for vaping and don't swallow the e-liquid.
http://www.istick.org/eleaf-ijust-one-starter-kit.html